Boat shoes are a great summer shoe that can be worn with just about any outfit. However, tying those laces can sometimes be difficult. Luckily for you, we have created this easy guide on how to tie boat shoe laces so you can enjoy your summer without worrying about it!
Instructions: How to Tie Boat Shoe Laces
Step One: Place the shoe on a flat surface. Then, thread each lace through the small hole on either side of your shoe’s front and then cross them over one another. This should create slack in both laces for you to tie a knot with at the end.
Step Two: Cross the laces so that they are parallel, and your left lace is now to the right of your right lace. This will create an X shape with both of them in one spot.
Step Three: Take your left lace from below, over and across it crosswise over the top of its partner. Now take this new loop end up towards where you want to tighten it at about three inches above where you put it down.
Clip off any excess length as desired before pulling tight by holding onto both ends near each other for stability or hold tightly while using pliers or clamps if needed for extra help tightening securely but do not pull too hard to avoid wrinkling the laces.
Step Four: Take the right lace from below, over and across it crosswise over the top of its partner. Now take this new loop end up towards where you want to tighten it at about three inches above where you put it down.
Clip off any excess length as desired before pulling tight by holding onto both ends near each other for stability or hold tightly while using pliers or clamps if needed for extra help tightening securely but do not pull too hard to avoid wrinkling the laces. You will now have a mirror image of your original X shape with one side higher than the other.
Step Five: Repeat steps two through four on opposite sides until all loose ends are neatly tucked inside the shoe for a smooth, tight finish.
Step Six: Cut off any excess laces left on top of the shoe and then use either nail clippers or scissors to carefully cut away the long-end pieces that are poking out from under the lace loops for an extra clean look.
Tips & Tricks
In this section, we’ll cover some tips & tricks on how to tie boat shoe laces.
Tip 1: Remember when cutting your loose ends, there is no need to trim them too close as you can always do this easily later in case they poke through again. If needed, grab some clear tape to cover up any exposed bits until you have time to shave it down with proper tools.
Tip 2: Make sure the front of your shoe is on a flat surface, and then put both hands on either side of that part. Grip it tightly, one hand to pull in down tight while the other stretches up as you move your thumbs from each end towards the middle of where they meet. This should create just enough slack in the laces for you to cross them over and tie a knot.
Tip 3: Use your fingers and thumbs as hooks, pulling them through each other in an overlapping fashion from one side of the shoe to the other. Put away that loop temporarily by laying it flat on top of itself before taking up its slack, so all four loose ends line up in the same direction. Then, take up all four ends by holding them one at a time and making an overhand knot.
Tip 4: Finally, tie off that final loop of loose lace with another overhand knot to secure it tight against your shoe’s front.
Frequently Asked Questions
Why Do Boat Shoes Have Laces on the Side?
To secure the shoe to your foot. Laces are used to tighten and make a snug fit around your ankle, while eyelets allow for air circulation by releasing pressure on hot summer days when you don’t want stiff leather against your skin.
How Tight the Shoe Laces Should Be?
How tight the laces should be varying from person to person. A typical rule of thumb is that you can fit one finger between your shoe and foot, but this may vary depending on how wide or narrow your feet are.
Why Are Boat Shoes Mostly Black?
Many people believe black boat shoes originated in the 1920s as the uniform of yachting clubs. The shoes were originally made with black tanned leather for their durability and waterproof qualities because they were worn at sea on boats that would be exposed to the elements. A secondary influence may have come from tennis attire, which was predominately white when this style first came into vogue.
Conclusion
The Shoelaces are the most important part of your shoe. They provide support and hold your foot in place, so it is essential to tie them correctly for a comfortable fit that lasts! If you are looking for a new way to tie your boat shoes, then this blog post on how to tie boat shoe laces is perfect for you!
It’s easy to tie your boat shoe laces. All you have to do is loop the lace over and pull it through! You can even use this technique with any type of shoelace, not just those on a pair of boat shoes.
Now you know the tricks. Don’t forget; the key is to pull tightly and make sure your ends are tucked in neatly before tying a bow or knot! Tie them tight for best results. Now go out there and show off how well you can tie your shoelaces!
You May Read Also – How to Tie a No-show Shoe Lace Knot
